86-13798264392
19c, Tower a, Guanghao Int. Centre, Meilong Rd., Longhua, Shenzhen, Guangdong, China
Huawei SDH OptiX Metro 100
Product Features
The OptiX Metro 100 supports various services interfaces, power input modes, and installation modes, and a high security mechanism.
Various E1 Service Interfaces
The OptiX Metro 100 supports three types of physical interfaces:
High Network Security Mechanism
The OptiX Metro 100 supports the Radius security control, that is, the user names and passwords of all NEs are managed in a unified manner through the server of the user. Any user must pass the authentication before logging in to the NE. Therefore, the network security is high.
Support for Device Stack
The OptiX Metro 100 supports a maximum of 1+3 device stack (one master device and three slave devices), that is, 16xE1 services are configured into one optical channel.
Support for Default Settings
The OptiX Metro 100 is configured and maintained with the NMS and Web LCT, supporting the "one-click recovery to default settings" function.
Various Installation Modes
The OptiX Metro 100 can be installed in various ways. Therefore, you can select a proper installation mode according to the actual situation.
The OptiX Metro 100 supports the following installation modes:
Various Power Input Modes
The OptiX Metro 100 supports the following power input modes:
The OptiX Metro 100 supports one AC power input and one DC power input at the same time. The two power inputs back up for each other. The AC power input is controlled by a switch, whereas the DC power input is not. When the AC power input and the DC power input are unavailable at the same time, the OptiX Metro 100 reports the VOLT_LOS alarm indicating a power failure.
Low Power Consumption, Natural Heat Dissipation, and High Integration
The OptiX Metro 100 supports SDH services,PDH services,Ethernet services.
| Service Type | Maximum Access Capacity |
|---|---|
| SDH services | 2xSTM-1 (o) |
| PDH services | 4xE1 |
| Ethernet services | 2xFE (e) |
| Functions and Features | Description |
|---|---|
| Basic function | Transmits and receives 4xE1 services. |
| Alarm and performance event | Supports various alarms and performance events, which facilitates the management and maintenance of the equipment; supports the alarm reversion function. |
| Clock source |
|
| Maintenance features |
|
| Overhead processing |
|
| Other functions | Supports three types of E1 interfaces: RJ-45 (120 ohms), BNC (75 ohms), and DB15 (X.21). |
Functions and features of the SDH unit
| Functions and Features | Description |
|---|---|
| Basic function | Transmits and receives 2xSTM-1 optical signals. |
| Alarm and performance event | Supports various alarms and performance events, which facilitates the management and maintenance of the equipment; supports the alarm reversion function. |
| Clock source | Supports the line clock extraction function. |
| Maintenance features |
|
| Overhead processing |
|
| Optical module |
|
Functions and features of the clock unit
| Functions and Features | Description |
|---|---|
| Clock protocol | Supports the Standard Synchronization Status Message (SSM) protocol. |
| Working mode | Supports the tracing mode, hold-over mode, and free-run mode. |
| Clock source | Supports the line clock extraction function.
|
Functions and features of the power unit
| Functions and Features | Description |
|---|---|
| Power supply types | Supports AC and DC power supplies. |
| Power supply protection | The AC power input and the DC power input back up for each other. When the two power inputs are unavailable, the VOLT_LOS alarm is reported. |
| Power detecting unit | Supports the detection on the AC power input and DC power input. When either of the power inputs fails, the POWER_FAIL alarm is reported. |
Ethernet features supported by the OptiX Metro 100
| Feature | Description |
|---|---|
| Ethernet frame encapsulation format | Supports the GFP-F, LAPS, and HDLC encapsulation formats. |
| Jumbo frame |
|
| Mapping mode | Supports VC-12 or VC-3 virtual concatenation. |
| Ethernet test frame | Supports Ethernet test frames. |
| Interface Characteristics |
|
| Loopback |
|
| LCAS | Supports link capacity adjustment scheme (LCAS). |
| LPT | Supports point-to-point link pass through (LPT). |
| RMON | Supports remote network monitoring (RMON). |
| Transfer or discard of frames shorter than 64 bytes | Supports the discard (default setting) or transfer of frames shorter than 64 bytes. This function can be enabled or disabled on the NMS. |
| Frames with frame check sequence (FCS) errors | Supports the transparent transmission of frames with FCS errors. This function can be enabled or disabled on the NMS. |
| Minimum frame length | Supports the setting of the minimum frame length to 64 bytes. |
Functions and features of the extended unit
| Functions and Features | Description |
|---|---|
| Basic function | Supports the aggregation of a maximum of 16xE1 services into one optical path. |
| Maintenance function | Supports loopbacks on stacking interfaces. |
Specification
| Specifications | Metro 100 |
|---|---|
| Aggregation | STM-1 |
| Dimensions | 43.6 mm (H) x 442 mm (W) x 220 mm (D) |
| Switch Capacity | 1.25Gbit/s full higher order and lower order cross-connect capacity |
| Supported Interfaces | STM-1(o), E1(e), FE(e) |
| Power Supply | DC: -48V DC or -60V DC AC: 220V/110V AC |
| Networking Mode | Supports multiple SDH networking topologies, such as chain, ring, tangent rings, intersecting rings, etc |
| Clock Synchronization | Line clock source Tributary clock source One external clock input/output (2 Mbit/s) |
| Auxiliary Interface | 10M/100M NM interface, external UPM management port, stack interfaces Alarm interface |
Cargo will be delivered within 1 day after payment arrived. Tracking Number will be offered once delivery done.
| Delivery Options | Estimated Delivery Time |
|---|---|
 | 3-5 business days |
 Fedex | 3-5 business days |
 By Sea | 10-20 business days |
Notice:
Above mentioned information are just for your reference only,we will keep you posted for the tracking delivery schedule.There are two delivery options available for by air and by sea:
Deliver to port:
Uonel is responsible for transporting goods to port. All subsequent customs and transportation fees are the
responsibility of the buyer. Uonel will recommend trustworthy local freight forwarders to you.Uonel can facilitate the progress under buyer's permission and at buyer's expense.
Deliver to door:
Uonel will quote all destination charge prior once we have confirmed order.
Uonel is responsible for transporting goods to door after you have made the payment.
100% Low Price Guarantee:
Uonel provides high-quality products at low wholesale prices
100% Quality Assurance:
All items are ORIGINAL NEW and GENUINE only.
Free Technical Support:
Our FREE Huawei Expert Consultancy Support is over the phone, by chat, by email or by login remotely.
100% Money Back Guarantee:
You can contact our customer service team to exchange or return any product that you bought from us.
Flexible Secure Payment & Shipment:
Verified authorization: Mcafee Secure, VeriSign Secured
Return Material Authorization (RMA) Process
Standard Hardware Warranty Policy:
Original new sealed Huawei product: 1 Year
The Support Contacts:
If your Huawei products failed, you must contact your sales representative to verify product failure. If the problem still can't correct by remote support methods i.e. email or phone support, the RMA procedure will issue.
Uonel is one of the biggest Huawei Network Hardware distributor in china, founded in 2008. We are a global provider of netwotking products with more than 5000 customers.
We provide original new Huawei Routers,Switches,Firewalls,Wireless APs & controllers,OLTs,GPON modems,optical transceivers.Our company have more than $5million Huawei products in stock.
Most of our technical engineers had work exprience in Huawei company,we can provide network design&planning,configration,troubleshooting,maintenance and training service in world wide.
